Home / Blogs / The making of one ring
How a custom ring is made
The making of one ring, from a photo to the finished piece
One client, one photo and one blue sapphire. We drew his ring, cast it, cleaned it and set his stone, and we filmed each stage. This is that ring’s story, and the clearest way we know to show how a custom ring is made.
The short answer
Six stages, one ring
A custom ring is made in six stages: the idea, the CAD drawing, the approved render, casting, cleaning and polishing, and stone setting. At Argentia we make custom rings to order in Argentium 960 silver in our workshop in Jaipur, around your idea and, if you like, your own stone. Below, one real ring goes through every stage.
Plate I

5 October
Chapter I
It started with one photo
A client sent us a photo of a ring he liked and his own blue sapphire of 7.6 carats. He had drawn green lines over the photo to show what he wanted: shoulders that sweep into a V under the stone.
That is all a custom ring needs to begin. A photo, a sketch or a few words tell us the idea, and the stone tells us the size.
Plate II

13 to 17 October
Chapter II
The drawing in CAD
Next, we drew the ring in CAD, the computer design software jewellers use to build a piece to exact measurements. The setting was drawn around his sapphire, so the stone would sit securely and close to the finger.
He asked for changes, and we made them in the drawing: the stone opened to a half bezel so more of the sapphire shows, and the shoulders reshaped into the V he wanted. Changing a drawing costs nothing; changing metal is slow and costly.
Plate III

17 October
Chapter III
Seeing it before it exists
From the CAD we made a render, a realistic picture of the finished ring. On 17 October he saw it and approved it.
This is the most important step for the client. The ring is fully decided before any metal is used, so there are no surprises when it arrives.
Plate IV
Late October
Chapter IV
From the casting
The approved design is turned into metal by casting. When the ring comes out, it looks nothing like the render: grey, dull and rough, with marks from the process.
Every cast piece begins like this. The shape and the details are all there; the shine comes in the next stage. The client asked us whether it looked a little rough at this point, and it did.
Plate V
November
Chapter V
Cleaned and polished
Next, the ring is cleaned, filed and polished until the silver shines like a mirror, inside and out. The engraved shoulders come to life, and the setting is checked before the stone goes in.
We heat-harden every piece twice for strength, and every piece is checked twice for quality before it moves on.
Plate VI
November
Chapter VI
The stone set
Last, his sapphire was set into the half bezel and checked again: the stone secure, the metal smooth around it, the ring true to the drawing.
Then we filmed it, as we film every finished piece, and sent him the video before it was packed. Two weeks from the approved drawing to this.
The whole journey
Six plates, one ring
I
It started with one photo
II
The drawing in CAD
III
Seeing it before it exists
IV
From the casting
V
Cleaned and polished
VI
The stone set
The dates
How long it took
Most pieces take two to three weeks after the design is approved. More on prices and how to start in personalised jewellery.
Your turn
Have an idea for a ring?
Send us a photo, a sketch or the stone you own. We will draw it, change it until it is right, and film it for you before it ships.
On WhatsApp at +91 82085 29473, or by email at toshit@argentia.in.
WhatsAppQuestions
Questions about custom rings
How long does it take to make a custom ring?
About two to three weeks after you approve the design. This ring took two weeks from the approved drawing to the finished piece; the drawing itself went through changes first.
What is CAD in jewellery making?
CAD is computer-aided design. The ring is drawn on a computer to exact measurements, so the setting fits the stone and you can see a realistic render and ask for changes before any metal is used.
Can I use my own stone?
Yes. This ring was made around the client's own 7.6 carat sapphire. Send us the stone's measurements, or the stone itself, and we draw the setting around it.
Can I change the design after seeing the CAD?
Yes. Changes are made in the drawing before casting, which is quick. In this ring, the setting was opened to a half bezel and the shoulders were reshaped before approval.
Why does a ring look rough after casting?
Every cast piece comes out dull and rough. Cleaning, filing and polishing bring out the shine and the detail, which is why the casting looks so different from the finished ring.
What is a half bezel setting?
A half bezel holds the stone with metal around two sides and leaves the other two open, so more of the stone shows while it stays secure.
Which metal do you make custom rings in?
Mostly Argentium 960 silver, which is purer than traditional sterling, highly tarnish resistant and needs no plating. We also make mixed-metal pieces, such as Argentium with gold.
Will I see my ring before it is shipped?
Yes. We film every finished piece and send you the video before it is packed, and we ship insured to any country.